General Information

S125 OEM board, used in S125 Proximity Reader, comes without the enclosure and cable groups for interested OEMs

S125 Proximity Reader, offered with variety of options, is a fully featured, multipurpose 125 KHZ RFID Proximity Reader.

S125 Readers can read and output 125 KHz EM410x type Card/Tag ID over Serial, Wiegand interface or do some custom operations including I/O, LED, Buzzer driving. 

Readers can be connected to the typical devices listed below or can act as a standalone device. Standalone mode is only supported by S125-E series.

• PC over RS232/RS485
• Wiegand Control Panels
• Panels or PLCs over RS232/485
• SAC 900 Sonmicro Access Control Terminal
• or can work in standalone mode (S125-E)
 

S125-ER « E Series », (E denotes, Built-In EEPROM memeory, R denotes Built-In Relay) , comes additionally with built-in E2PROM memory and 60W Relay, supports standalone working mode with 1000 user capacity. S125-ER can work as a standalone access control device and trigger a relay or do some custom operations once the Tag ID is found in the EEPROM memory.  

S125-ER Series is appropriate for basic access control with standalone operation mode and can also be used in complicated time & attendance systems with online mode operation. 

Standalone feature allows no requirement for a controller device to be connected. A defined Master Card can store User Cards or delete them from the built-in memory, eliminating any second device requirement such as PC. By using standalone feature, basic access control is implemented. It can be connected to elevators, electrical doors and user granted access is implemented very quickly.

Features

• 125 KHz RFID EM4100/02 (Unique) Cards & Tags
   
• Online & Standalone Operation ¹
   
• Built-In E2PROM Memory up to 1000 Users ¹
   
• Teach & Delete with Master Card ¹
   
• Fully customizable & firmware Upgrade-able ² 
   
• 9V/12V DC Operating Voltage, AC Input (optional) ³
   
• RS232/485 Interface 9600bps to 115200bps ⁴
   
• Wiegand Interface (26/34/42 bits)
   
• 1x 60W Built-In Relay (NO,NC,COM) ⁵
   
• 1x Opto-Isolated Input ⁵
   
• Built-In Buzzer & BiColor LED
   
• 2x General Purpose 5V (I/O) instead of Wiegand. (Can control 2x 120W Relays coming with SA-100 Easy Connect & Expansion Accessory)
   
• Advanced & Intelligent SingleWire Input Control ⁶
   
• Appropriate for Wall-Mount
   
• Compatible with SonMicro’s SAC 900 Access Control Terminal
   
• Easy & Smooth wiring accessories available
  

¹ Standalone operation is available only on S125-E Series
² Hardware and Firmware customization is available. “No Name” service is available for OEMs
³ SA-100 Connector accessory includes built-in AC/DC regulator for AC Voltage inputs. (Solds seperately)
⁴ RS232 and RS485 comes as different products and are not supported at the same time
⁵ Two of the Wiegand Data Line can be converted to 5V Inputs or Outputs in Configuration Software.
⁶ Inputs can detect and warn if state is high or low. Pulses on input wire can be counted
 

Pricing Information

S125 Readers are specifically designed for OEM Manufacturers, System Integrators and/or for Reseller & Distributors.

Please contact us to request quoatation based on quantity.

For evaluation purpose or indivudual buyings you can buy a full kit from our online store.

Click to buy S125 Evaluation Kit from our online store

Please notice that S125 Readers are not available thru our online store as a single device. It comes as an evaluation kit with all accessories to run and evaluate quickly.
For single S125 Reader purchasements at reasonable prices, please directly contact with us.

Downloads

 Brouchure & Ordering Guide

 User Manual 

 Connection Diagram

 S125 Configuration & Demonstration Software (4.2 Mb)